Central Vascular Access Device (CVAD): Flushing

Overview

A CVAD should be flushed as often as your doctor tells you, to keep it clear of blood and prevent clotting. If it ends in more than one line (lumen), flush them in the same order each time. Depending on the type you have, you will flush it with either heparin or saline solution. Your doctor or nurse will probably give you supplies and instructions on how to flush it. A nurse may come to your home to help you at first.

You will usually lie down when you flush the line. This helps prevent air from getting into your vein.

Preparing the syringe or cannula

  1. Be sure you have all your supplies ready. These may include the heparin or saline solution, syringes, needleless injection cannulas, alcohol swabs, and a disposal box. What you need will vary with the type you have. You may have syringes that are already filled with the solution (preloaded).
  2. Wash your hands with soap and water for 15 to 30 seconds. Dry them with paper towels.
  3. Wipe the stopper of the heparin or saline solution bottle with an alcohol swab for 15 to 30 seconds.
  4. Remove the cover from the syringe, and twist the needle or cannula on to it. (It may already be attached.)
  5. Remove the cover from the needle or cannula. Note: If you have a preloaded syringe, skip to the next section, "Flushing the line."
  6. Pull back the plunger of the syringe, and draw air into the syringe equal to the amount of heparin or saline solution you are using.
  7. Push the needle or cannula through the rubber lid of the solution bottle.
  8. Push the plunger of the syringe to force air into the bottle.
  9. Turn the bottle and syringe upside down. Position the tip of the needle or cannula so that it is below the surface of fluid in the bottle. Pull back the plunger to fill the syringe with the amount of solution you need.
  10. Before you take the needle or cannula out of the bottle, check for air bubbles in liquid in the syringe. If there are bubbles, push the plunger back in and then pull back on it again.
  11. Remove the needle or cannula from the bottle.
  12. Fill other syringes if you need to flush more than one lumen.

Flushing the line

  1. Use an alcohol swab to rub the cap of the line you want to flush. Rub for 15 to 30 seconds, and then let the cap dry.
  2. Hold the end of the line so it does not touch anything.
  3. If you have a clamp on the line, open it.
  4. Slowly inject heparin, or quickly inject saline solution. If there is resistance, stop. Do not force it. Call your doctor.
  5. If you have a clamp on the line, clamp it as you are finishing the injection and then remove the syringe. If the line has a positive pressure cap, remove the syringe and then clamp it.
  6. Put the syringe in the disposal box.
  7. Repeat the above steps for each line you are flushing.
  8. Wash your hands again with soap.

Credits

Current as of: January 20, 2022

Author: Healthwise Staff
Medical Review:
E. Gregory Thompson MD - Internal Medicine
Adam Husney MD - Family Medicine
Kathleen Romito MD - Family Medicine
William H. Blahd Jr. MD, FACEP - Emergency Medicine

Disclaimer: The information contained in this website, and its associated websites, is provided as a benefit to the local community, and the Internet community in general; it does not constitute medical advice. We try to provide quality information, but we make no claims, promises or guarantees about the accuracy, completeness, or adequacy of the information contained in or linked to this website and its associated sites. As medical advice must be tailored to the specific circumstances of each patient and healthcare is constantly changing, nothing provided herein should be used as a substitute for the advice of a competent physician. Furthermore, in providing this service, Adventist HealthCare does not condone or support all of the content covered in this site. As an Adventist health care organization, Adventist HealthCare acts in accordance with the ethical and religious directives for Adventist health care services.

Find a Doctor

Find an Adventist HealthCare affiliated doctor by calling our FREE physician referral service at 800-642-0101 or by searching our online physician directory.

View Doctors

Set Your Location

Setting your location helps us to show you nearby providers and locations based on your healthcare needs.